Differences

This shows you the differences between two versions of the page.

--- documentation:examples:pppoe_and_l2tp_lab [2021/04/01 11:36] – [Router 2] olivier
+++ documentation:examples:pppoe_and_l2tp_lab [2021/04/01 11:44] – [Router 3 : LNS (L2TP server)] olivier
@@ Line 62: / Line 62: @@
 ===== Routers configuration =====
-==== Router 1 ====
-Router 1 is configured as a simple workstation : PPPoE client.
+==== Router 2 : BAS and LAC ====
-Note: There is no IP address configured on the ethernet interface.
+Router 2 forwards PPP between PPPoE and L2TP.
-<code>
-sysrc hostname=R1
-sysrc gateway_enable=NO
-sysrc ipv6_gateway_enable=NO
-sysrc mpd_enable=YES
-sysrc mpd_flags="-b -s ppp"
-cat > /usr/local/etc/mpd5/mpd.conf <<'EOF'
-default:
-        create bundle static B1
-        set bundle enable ipv6cp
-        set ipcp enable req-pri-dns
-        set ipcp enable req-sec-dns
-        set iface route default
-        create link static L1 pppoe
-        set link action bundle B1
-        set auth authname olivier
-        set auth password secret
-        set pppoe iface vtnet0
-        open
-'EOF'
-service netif restart
-service routing restart
-service mpd5 start
-config save
-</code>
-==== Router 2 ====
-Router 2 is configured as a BAS and LAC (forward PPP between PPPoE and L2TP).
-=== Modify configuration ===
-Set the base parameters:
 <code>
 sysrc hostname=R2
-sysrc ifconfig_em1="10.0.23.2/24"
+sysrc ifconfig_vtnet1="10.0.23.2/24"
 sysrc mpd_enable=YES
 sysrc mpd_flags="-b -s ppp"
@@ Line 109: / Line 76: @@
 default:
         create link template L1 pppoe
-        set pppoe iface em0
+        set pppoe iface vtnet0
         set link action forward L2
         set link enable incoming
@@ Line 121: / Line 88: @@
 </code>
-==== Router 3 ====
+==== Router 3 : LNS (L2TP server) ====
-Router 3 is configured as a LNS (L2TP server).
-=== Modify configuration ===
-Set the global parameters:
 <code>
 sysrc hostname=R3
-sysrc ifconfig_em1="10.0.23.3/24"
+sysrc ifconfig_vtnet1="10.0.23.3/24"
-sysrc ifconfig_em2="88.88.88.4/24"
+sysrc ifconfig_vtnet2="88.88.88.4/24"
 sysrc mpd_enable=YES
 sysrc mpd_flags="-b -s ppp"
-</code>
-Configure mpd5:
-<code>
 cat > /usr/local/etc/mpd5/mpd.conf <<'EOF'
 default:
@@ Line 154: / Line 111: @@
         set link enable incoming
 'EOF'
-</code>
-Set the password:
-<code>
 cat > /usr/local/etc/mpd5/mpd.secret <<'EOF'
 olivier         secret
 'EOF'
+service netif restart
+service routing restart
+service mpd5 start
+config save
 </code>
-And apply your changes:
+==== Router 1 : : PPPoE client ====
 <code>
+sysrc hostname=R1
+sysrc gateway_enable=NO
+sysrc ipv6_gateway_enable=NO
+sysrc mpd_enable=YES
+sysrc mpd_flags="-b -s ppp"
+cat > /usr/local/etc/mpd5/mpd.conf <<'EOF'
+default:
+        create bundle static B1
+        set bundle enable ipv6cp
+        set ipcp enable req-pri-dns
+        set ipcp enable req-sec-dns
+        set iface route default
+        create link static L1 pppoe
+        set link action bundle B1
+        set auth authname olivier
+        set auth password secret
+        set pppoe iface vtnet0
+        open
+'EOF'
 service netif restart
 service routing restart
@@ Line 177: / Line 152: @@
 Router 4 is configured as simple host, and be used an Internet server too for testing connectivity with the PC.
-=== Modify configuration ===
-Set the basic parameters:
 <code>
 sysrc hostname=R4
 sysrc defaultrouter="88.88.88.4"
-sysrc ifconfig_em2="88.88.88.5/24"
+sysrc ifconfig_vtnet2="88.88.88.5/24"
+sysrc gateway_enable=NO
+sysrc ipv6_gateway_enable=NO
 service netif restart
 service routing restart